EGEYAT 50 SPECIFICATIONS
Overall length : 15,55 m. Hull length : 15,24m.
Waterline length : 14,10 m. Beam : 4,75 m.
Draft : 2,20 m. Displacement : 12,400 kg.
Ballast : 4100 kg. Berths : 8-10
Sail areas : 124 m2 Engine : 110 Hp.
Hull : Hand made solid laminate Fiberglas mat and rowing .
Deck : Deck is moulded Fiberglas with sandwiched marine plywood, stress areas where winches, sheet tracks, etc. are reinforced by using backing chrome plates.
Ballast : 4100 kg. cast iron, torpedo shaped bottom. Keel bolts are of stainless steel.
Rudder : GRP rudder on solid stainless steel stock (70 mm. diameter).
Motor bed : GRP bed moulded to the hull.
Chain plates : Stainless steel fixed on the hull.
Teak cockpit : Teak cockpit is laid from 10 mm. First class teak ribs bonded to the deck with epoxy resin and secured by stainless steel screws. Expansion joints sealed by special polyurethane silicone.
Interior joinery : Marine grade water proof plywood faced with selected Mahogany or American Cherry is used in all bulkheads and major joinery. Specially selected solid Mahogany or beech in frames and doors. Marine plywood in bottoms, shelves, etc. where not visible. All main bulkheads bonded to the hull and deck using glass mat and polyester. Ceiling, top sides and visible hull sides padded with foam backed vinyl. Hullsides, bottom, bilge, etc, topcoated throughout the interior. Varnished cabin sole, Mahogany with Ash-Tree inlaid wood stripes.
Forward cabin : Large double berth and wardrobe on s.b. side, stowage under the berth , shelves along hullsides sb. and port side.
Saloon : U- shaped settee on port side with fixed table. There is another table at the other side of the table. Stowage under the settee . A settee in SB side at the back of navigation area.
Aft Toilet : GRP basin unit. Lockers along hull side, GRP moulded bottom section drained by electric pump.
Master cabin toilet : GRP basin unit. Lockers along hull side, GRP moulded large shower base drained by
Galley : Galley on starboard; Ice-box with 12 V Danfoss compressor, double sink, drawer section, dry food locker. 2 burners gas stove with oven. The ice-box is drained
Navigation area : Large navigation table with stowage for charts etc. Electrical master panel mounted in bulkhead locker, navigation seat
Aft cabins : Large two aft cabins with double berths and wardrobes. Shelves along hull side stowage under the berth.
Captain Cabin: As an optional, it is possible to build a captain cabin with a stand alone entrance according to owner’s willing.
Interior plans can modified according to customer willings. For EGE 50, it is possible to build with 4 cabins+ captain cabin or with just 4 cabins. It is also possible to build with only with two master cabins. All interior plans are confirmed before building by the customer.
DECK EQUIPMENT :
-4 hatches, 3 large windows
-2 46 STA Harken winches, 2 60 STA Harken winches
-4 mooring bollards
-2 aluminum genoa tracks with rails
-1 main sheet track with slider and tag lines
-25 mm. diameter stainless steel pullpit, pushpit and ladder
-1400 w. Electric anchor winch
-Solimar brand pedestal and stainless steel steering wheels with leather cover, compass and acceleration lever fitted, engine panel is in the cockpit.
General ; bolts, nuts, washers and screws used for fastening deck equipment are of stainless steel
Sealing used between deck and equipment is polyurethane, silicone or specially developed material
INTERIOR EQUIPMENT :
Fresh water system : 250 lt. capacity fiberglass tanks with level meter. Pressurised water.
Filler line from deck. Tanks are ventilated.
Shower arrangement in toilet. Double sink and wash basin drained either through hull or to the waste water tanks by means of ball valves. Hot water is optional extra. 2 waste water tanks.12 volt bilge-pump.
Toilet installation : Hand operated marine toilet with sea water in take and outlet through ball valves. Waste holding tank and Y valve. Electric toilet is optional extra.
Shower : Shower basin is drained by electric drainage pump, operated by manual switch in shower compartment.
Cushions : Cushions in high quality foam with first class upholstery in choice of colours.
Electrical installation : Switchboard and control panel in navigators area. 2 reading lights in forward cabin, 1 fluorescent lamp in toilet, 4 spotlights in main cabin, 1 fluerescent lamp in pantry, 1 navigators light, 1 reading light in aft cabin, 2 x 105 amp/hrs. marine batterys, 1 both shalter.
Gas system : 1 small gas bottles ( 4.95 liters) installed in separate, drained compartment on deck.Reduction valve for low pressure system.2 burner gas stove with oven.
General Hardware : Doors have marine locks. Locker doors have finger snap locks and are hinged with brass hinges.
General : Bolts, nuts, washers and screws are generally stainless steel. Hose clamps are all stainless steel. Through bottom fittings and other piping fittings are brass. Hoses are reinforced flexible pvc polyethylene.
ENGINE INSTALLATION :
Engine : 110 Hp. Yanmar diesel with fixed propeller . Fresh water cooling .
Controls : Lever controller and instrument panel in cockpit.
Fuel : 150 liters diesel tank in stainless steel with level meter. Filling from deck.
Engine housing : Easily removed engine housing with interior joinery finish, well insulated with foam.
Battery : 2 x 105 amp/hrs. battery with both shalter.
MAST AND RIGGING :
Main mast : Selden brand furler mast and furler cenoa with two levels of spreaders, boom and boomvang.
Standing rigging : All stays and shrouds in stainles steel wire.
Running rigging : 1 main halyard, 1 cenoa halyard, 1 main sheet, 2 jib sheets.
Sails : UK/ Halsey brand 1 main furler , 1 genoa furler , sail bags.
Autohelm brand deep sounder and speed indicator.
STANDART EQUIPMENT :
4 Mooring lines
1 Anchor with chain
1 Instruction manual